-40%
HV High Voltage Power Supply Kit for PMT Photomultiplier / Geiger tube 1500V max
HV High Voltage Power Supply Kit for PMT Photomultiplier / Geiger tube 1500V max
HV High Voltage Power Supply Kit for PMT Photomultiplier / Geiger tube 1500V max
HV High Voltage Power Supply Kit for PMT Photomultiplier / Geiger tube 1500V max

HV High Voltage Power Supply Kit for PMT Photomultiplier / Geiger tube 1500V max

$ 31.66

  • Application: Hobby DIY Projects
  • Based on: TL494
  • Brand: Unbranded/Generic
  • Country/Region of Manufacture: Israel
  • Electrical circuit: NOT INCLUDED
  • High Voltage output type: Positive HV regulated DC
  • Input Voltage: 12V DC
  • Input current: 15mA - 50mA
  • MPN: RH-M-PMT-HVPS
  • Model: RH-M-PMT-HVPS
  • Output Power: 0.2W max
  • Output Voltage with 100 Meg load: 150V - 1500V
  • PCB Edition: ver.3b
  • Radiation Detector Type: Scintillation Detector
  • Recommended load for spectroscopy: ~100 Mega Ohm divider
  • Topology: Boost PWM ~60KHz
  • Type: Radiation Detector
  • UNI-T Voltmeter on the photos: NOT INCLUDED
  • UPC: Does not apply
  • gtin13: Does not apply

Description

New 3.0 Revision of Adjustable HVPS DIY High Voltage Module for Photomultiplier Tube 150V - 1500V. This power supply has positive adjustable high voltage output 150V - 1500V (under 10Meg. load) and can be used for DIY Photomultiplier Scintillators, Amateur PMT Projects or for powering Geiger tubes. High Voltage can be adjusted manually with on-board potentiometer or through Digital SPI interface. You need to set the DIP-Switch to select desired controlling method. Example control code for Arduino can be downloaded in Github repository. https://github.com/RH-Electronics/MCP41010T Technical Specifications: Positive Polarity High Voltage stabilized output: 150V-1500V Compatible with DIY Scintillation Probes and Geiger Tubes Digital SPI Control or Manual Potentiometer Control Input DC voltage: 12V Input current consumption : 10mA - 50mA Output power: 0.2W Recommended load of the PMT probe divider: 80-100 Mega ohm Minimum Load: 10Mega ohm Topology: Boost TL494 PWM ~60KHz (easy to filter) Output RC filter included Shipping Weight: 180gr SKU: RH-M-PMT-HVPS This is regulated stabilized HVPS power supply for DIY hobby projects. The module can be used to power several Geiger tubes or PMT tube in gamma scintillation project. Circuit uses PWM high frequency conversion of ~60KHz. It easy to filter the noise because of high conversion frequency. The board of the power supply has installed RC filter to reduce noise factor. 5-Pin connector pinout: GND - for external microcontroller ground reference 5V OUT - allows to power external low profile microcontroller SDI - SPI data input SCK - SPI clock input CS - SPI Chip Select, Active -HIGH DIP-Switch Selector: You must set just one of the illustrated dip-switch pre-sets. DIGITAL: 1-ON ; 2-ON; 3-ON; 4-OFF; 5-OFF; 6-OFF MANUAL: 1-OFF ; 2-OFF; 3-OFF; 4-ON; 5-ON; 6-ON By default, shipped with MANUAL pre-set. Recommended to be purchased with our Pulse Amplifier: https://www.ebay.com/itm/322575299576 HV is DANGEROUS! You are fully responsible for any technical damage or health injury caused by this electronic device. We'll use the best shipping method available to your destination, however some areas and some countries now will take much longer to receive international mail. Please allow longer delivery time than usually and contact me prior buying if you want to change delivery method.